Conrod Dimensions

Discussion in 'Technical' started by tassuperkart, Aug 9, 2010.

  1. tassuperkart

    tassuperkart Its a lie I tell you!

    Messages:
    2,300
    Likes Received:
    26
    Trophy Points:
    48
    Where can i find these?
    Is it true that the conrods are the same as RB26?
    L8r
    E
     
    tassuperkart, Aug 9, 2010
    #1
  2. Chrispy

    Chrispy Pretentious Upstart

    Messages:
    12,888
    Likes Received:
    368
    Trophy Points:
    83
    First I've heard of it :confused:
     
    Chrispy, Aug 9, 2010
    #2
  3. Tech@EPR

    Tech@EPR Member

    Messages:
    452
    Likes Received:
    17
    Trophy Points:
    18
    FSM has all the tech data on stock rods that you would need.
     
    Tech@EPR, Aug 9, 2010
    #3
  4. tassuperkart

    tassuperkart Its a lie I tell you!

    Messages:
    2,300
    Likes Received:
    26
    Trophy Points:
    48
    Sorry M8, but what is FSM?
    E
     
    tassuperkart, Aug 9, 2010
    #4
  5. Chrispy

    Chrispy Pretentious Upstart

    Messages:
    12,888
    Likes Received:
    368
    Trophy Points:
    83
    Factory service manual.

    It's in the tech section.
     
    Chrispy, Aug 9, 2010
    #5
  6. tassuperkart

    tassuperkart Its a lie I tell you!

    Messages:
    2,300
    Likes Received:
    26
    Trophy Points:
    48
    Ohhh K... * blushes* my bad!
    Ill look then.
    Thanks Men
    E
     
    tassuperkart, Aug 9, 2010
    #6
  7. tassuperkart

    tassuperkart Its a lie I tell you!

    Messages:
    2,300
    Likes Received:
    26
    Trophy Points:
    48
    All I can find is rod center to center length and pin diameter............................
    hellp!
    E
     
    tassuperkart, Aug 9, 2010
    #7
  8. a2zed

    a2zed Guest

    If you can get rb26 rod dimensions, I can measure a VG rod for you tomorrow.
     
    a2zed, Aug 9, 2010
    #8
  9. Tech@EPR

    Tech@EPR Member

    Messages:
    452
    Likes Received:
    17
    Trophy Points:
    18
    well specifically what information are you needing? The info you stated above is the jist of what most really need in tech data. Please be specific in what data you need in comparison.
     
    Tech@EPR, Aug 9, 2010
    #9
  10. tassuperkart

    tassuperkart Its a lie I tell you!

    Messages:
    2,300
    Likes Received:
    26
    Trophy Points:
    48
    Well, center to center, pin diameter (both ends) and the widths at the pin end and crank bearing end.
    Im confirming rod dimensions with a supplier of Chro-Mo H-beam rods.
    Just want to be sure.

    The RB/VG comparison was something I have heard about in the past but never actually checked out as fact or fiction.

    L8r
    E
     
    tassuperkart, Aug 9, 2010
    #10
  11. rollin

    rollin First 9

    Messages:
    5,366
    Likes Received:
    36
    Trophy Points:
    48
    i think they are the same as CA18 rods. dunno if that helps. lol
     
    rollin, Aug 9, 2010
    #11

Share This Page