OK guys this is partly a re-post. Thanks to all for the previous interest and so on, but it's time to move forward. Had plenty of interest in the good bits but as always there's been plenty of wind, so here's the updated list of what's there. PM me for specific info. Parts located in Wangara, WA and can be inspected by appointment during business hours. I can also be contacted by phone on 0418822444 with caller ID. Dont waste my time with stupid offers etc, and please post only if it's relevant. Rolling Shell 1990/91 2 Seater $2500 Painted in Nissan Blue-ish Green (factory colour for the Pintara in about 1990) Was black. Paint faded but in good condition otherwise. Fitted with green compliance plate and is currently unregisterred. It is complete minus the parts listed for sale below, PIAA low beams, Laserline Alarm, No Stereo, radiator or front bar, no hicas. Would make a good parts car, race car, project or whatever. At this stage I am NOT separating panels or trims etc. Nismo speedo $300 300km/hr. It is what it says. Dont ask for pics of this - you either know what it is or you dont. Same for the mileage - the Z speedo does not contain the odo. Engine with Upgrades $3,500 Good used engine fitted with new cam seals, rear main seal, front seal etc etc, New water pump and all hoses (silicone on the head bypasses) new thermostat, new timing belt, spark plugs etc as per 100,000k service, Modded PCV set-up and Breathers (no oil in plenums!!), Ported Exhaust manifolds (ceramic coated), Rebuilt/matched pair T25G turbo's (ceramic coated) Has never been run since work done. All upgrade parts are still NEW. 4inch Trust Single system - Cat Back $900 BORDER front mount cooler and pipe kit - $2200. Brand new never run, but has been installed. This is THE BEST KIT you can buy. Cost me over $4k to buy new. Twin intakes (in original intercooler position) $500 Has twin 6" JWT POP Chargers and requires either aftermarket ECU or remapped stocker. Piping made from 3" stainless. Cleaners have been used for a while when I had side mounts but the whole conversion itself has not been run. Engine wiring harness $800 genuine nissan, still in box, BRAND NEW OS Giken twin plate clutch/flywheel $1200 Excellent condition, no typical wear/abuse. Has reshimmed fingers. Discs are 3.2 and 3.1mm thick, the centre plate is 4.6mm and there is a total of 2.2mm of clamp load on the assembley. When assembled, the pressure plate fingers are just above flat, indicating good pedal travel, no over-centreing and reasonable life expectancy. I have a set of new flywheel bolts that have been machined to the correct length and test fitted, and the correct thrust bearing carrier.There is also a new thrust bearing. Manual Gearbox $1200 good condition low-k 5 Speed box with shifter, new shifter bushings, RG Racing Gear Coil-overs JTC N1 $2000 Again brand new, but fitted. These are the (at the time) top spec damper that RG made. Have excellent spring and damping rates. Will not disappoint. Worth over $3500 R32 GTR front brakes $500 Painted calipers (black), good pads, good rotors, surface rust. Volk 17x8/9's with 235/255 tyres $800 Yeah, average condition. clean up OK. Tyres knackered from age but are still round and black! No centre caps. Coil-packs, excellent condition $200 Standard ecu $200 suit remapping, replacement whatever Aluminium crankshaft pulley $150 Brand new, underdrive, which I had hard anodised Fan Belts $50 1 set of brand new, genuine Nissan R32 GTR rear brakes $250 painted (black) calipers, good pads and good condition slotted rotors HiCas Lock Bar $100 complete with tie rod ends and arms, ready to go in
