ProckyZ from show to GO!

Discussion in 'Member's Garage' started by ProckyZ89, May 3, 2012.

  1. lidz

    lidz Well-Known Member

    yeah it might be a while between updates but when they come through it's always top shelf!
     
    Harts likes this.
  2. ProckyZ89

    ProckyZ89 Senior Member

    67C74D2E-CE69-402C-AFE2-C09777DA40D9.jpeg 67C74D2E-CE69-402C-AFE2-C09777DA40D9.jpeg 53A976C0-3F99-4757-9DE3-2B87DD364374.jpeg

    Parts all returning from ceramic coating
    *intake manifold
    *exhaust manifold
    *intake pipework hot and cold
    *turbo compressor and turbine
    *cam covers
    *catch can
     
    ivan129, MintZ32, Harts and 1 other person like this.
  3. lidz

    lidz Well-Known Member

    Nice one Procky, keep the updates coming! Do you have a timeline for this?
     
  4. ProckyZ89

    ProckyZ89 Senior Member

    When you say timeline? Do you mean a completion date? Orrrrr...?

    if you mean timeline date. Expecting to be tuning end of April.
    Pending no issues with start up and testing for cooling system, oil pressure, oil temps, thermo van, amperage or the power steering set up
     
    Harts likes this.
  5. lidz

    lidz Well-Known Member

    yeah sorry that wasn't very clear! Yes meant completion on your current engine work.
    5 weeks or so will come up fast, hope you get a great result.
     
  6. ProckyZ89

    ProckyZ89 Senior Member

    its only been nearing 2 years

    going to be very interesting how these G25-660 .72 perform with the ideal set up to remove restrictions and enable proper breathing
     
    Harts likes this.
  7. ProckyZ89

    ProckyZ89 Senior Member

    B71C8235-A378-4F56-80BC-645DD9BDA4B0.jpeg Enter the final stages

    some good pics of my set up back from coating. full V band with plazmaman intake clamps- no bead or blowing pipes or shit off this time round.
    4A9E51D4-F701-4BA4-9F07-904E3C7C7D28.jpeg
     
    beaver, ivan129 and Harts like this.
  8. ProckyZ89

    ProckyZ89 Senior Member

    The OS Giken Quad plate is mounted up now.
    R35 coils ready to be wired in.
    Bde trans Mount got a slight modification for the exhaust as it was a late addition but still works fine.

    Lower plenumcthreads were a little chewed up so they’ve been cleaned up also.
     
    Harts likes this.
  9. ProckyZ89

    ProckyZ89 Senior Member

    Jesus I’ve been slack on this.

    so after a boat load of person crap that affected finance and held shit up.
    It’s been started, now doing some additional sensor wiring
    995170A9-D148-41BA-910A-8C7269C10B0E.jpeg 36B1F598-C837-405E-AA7B-35DE57E4DAD3.jpeg 17CAA95A-A7EE-40C1-B5CE-AFCAE00A3933.jpeg D62F31E8-1C5C-45A3-8B76-C1F3642DCEB9.jpeg 381445EE-0FE7-47BA-9CE0-560D2A7E5040.jpeg B8B62B06-EE79-4078-B60E-E0AF57C188E2.jpeg 4BD83D59-B6F4-4B27-A1A8-882E63B09015.jpeg
     
  10. MORBOOST

    MORBOOST Active Member

    I read os triple plates break gearbox's can only imagine what a quad does, which gear set you going with? If you end up going with the gm spline option used in most dog sets, have a look on rhdjapan for the clutch centre that will fit your clutch and gm spline I saw it once all though might only fit triple (different company to os giken) unless gtr centres are the same then os makes those.
     
  11. ProckyZ89

    ProckyZ89 Senior Member

    so I’m staying stock box (98+ spec) for initial work.

    The quad plate has the same cover as skylines.
    I am looking at a helical dog box 1-4 soon pending funds.

    what would be more ideal is a 3.9 rear differential …
    Just saying…
     
  12. MORBOOST

    MORBOOST Active Member

    got ya after I commented I remembered you use this for the snowy event which the box would be slightly less strained than drag strip work.
    this is what I was crappy on about https://www.rhdjapan.com/orc-1000f-sp-triple-plate-center-hub-holinger-shaft.html
    [​IMG]
    They call it holinger shaft but its just the GM size shaft option used in in most dog sets this is the 3 disc hub, I mentioned it cause they list it for z32 but thinking about it more I think the os gtr hub would be the same too suit your clutch

    [​IMG]
    this is a pic comparing the size difference to the stock shaft, worth it it my eyes just sorting the hub is something to think about. (note to future readers: if you go dog and want gm shaft buy os giken triple or quad or other rebuildable multi clutch kits with the hub I posted above)

    [​IMG]
    Still haven't found a answer if this billet centre plate for a gtr also an option for most dog sets fits the z32 casing.

    Good luck procky car looking dialled.
     
  13. MORBOOST

    MORBOOST Active Member

    See your selling you gearbox what are you replacing it with?
     
  14. ProckyZ89

    ProckyZ89 Senior Member

    Sorry- don’t get on too often.

    its now running a ppg helical dog box 1-4
     
  15. ProckyZ89

    ProckyZ89 Senior Member

  16. Harts

    Harts Active Member

    It lives!
     
  17. ProckyZ89

    ProckyZ89 Senior Member

    It’s ALIVE!!!! And Jesus does it sound good





    413 Rhkw with very conservative timing at all of 15psi

    fuel upgrade and alternator upgrade coming then it’s wind up time.
     
    Harts, SRB-2NV, lidz and 2 others like this.
  18. Harts

    Harts Active Member

    Sounds like a monster, can't wait to see what happens with the wick turned up.

    So lumpy, sounds almost like a worked V8! Ehat cams are you using?
     
  19. ProckyZ89

    ProckyZ89 Senior Member

    Wind up!! Boost and Wasps unleashed
     
  20. MORBOOST

    MORBOOST Active Member

    nice, can a ask why jem stopped at that rpm looks like it is still making power?
     

Share This Page