squeeling alternator belt

Discussion in 'Technical' started by BlaZeit, Oct 21, 2007.

  1. BlaZeit

    BlaZeit New Member

    Messages:
    939
    Likes Received:
    0
    Trophy Points:
    0
    hey guys my alternator belt has been squeeling so i've got under the car this morning and have tightened the belt adjuster, i was able to tighten it but only a couple of turns of the spanner before it reached the maximum it could be adjusted. The belt still seems a little loose compared to the others and now when i turn the car on the squeel does not go away as before it would go away after about a minute.

    Is there anywhere else where you can adjust the tightness of this belt or could it be that the belt has stretched too much?

    Any help would be appreciated.
     
  2. Chrispy

    Chrispy Pretentious Upstart

    Messages:
    12,888
    Likes Received:
    368
    Trophy Points:
    83
    Nup, belt has stretched too far. Buy a new one. You could just use some belt grip in the meantime
     
  3. K-zed

    K-zed Secret Squirrel

    Messages:
    8,030
    Likes Received:
    39
    Trophy Points:
    48
    NA stock alt belt 4PK 1015

    Get a new one Ben. :D
     
  4. Mitch

    Mitch Has one gear: GO

    Messages:
    1,919
    Likes Received:
    69
    Trophy Points:
    48
    Left field reply:
    There are two bolts to undo to tighten the belt: One at the front, and the one that points to the side of the vehicle. Both need to be loosened to tension the belt. The front bolt allows the tensioning cradle to slide / lock closed, while the side bolt only tensions until you clamp it off again.
    In my younger and more vulnerable years, i stripped a thread because i muscled it too hard and didnt know that 2 bolts needed to be undone.
     
  5. LOWZX

    LOWZX Banned

    Messages:
    9,187
    Likes Received:
    30
    Trophy Points:
    0
  6. K-zed

    K-zed Secret Squirrel

    Messages:
    8,030
    Likes Received:
    39
    Trophy Points:
    48
    Good point Mitch

    Could also be the power steering or air con belt so may as well replace all 3 if of a similar age.

    NA std P/S belt: 3PK 925 A/C: 4PK 960
     
  7. DinoZ

    DinoZ Talks sh#t for a living.

    Messages:
    1,740
    Likes Received:
    3
    Trophy Points:
    38
    While the alternator belt is off - spin the pulley by hand to check if there is any bearing wear in the alternator.
     
  8. BlaZeit

    BlaZeit New Member

    Messages:
    939
    Likes Received:
    0
    Trophy Points:
    0
    cheers guys, yeah i know about the two bolts :) did my homework before tightening, agree may as well do all the belts so car will be off to Gavin as i probably won't have the time to do the job during the week (not to mention that i've never removed/replaced belts before) and i can't stand the squeeling for a whole week. :eek:
     
  9. BlaZeit

    BlaZeit New Member

    Messages:
    939
    Likes Received:
    0
    Trophy Points:
    0
    Alternator belt fixed

    Took the Z to Gavin Woods today and he found that the bolt holding the alternator on had come away and was hanging :eek: it seems that someone in the past put the wrong bolt back in so all that was holding it on was the bolt at the adjuster.

    Well all fixed thats the main thing!
     
  10. K-zed

    K-zed Secret Squirrel

    Messages:
    8,030
    Likes Received:
    39
    Trophy Points:
    48
    Good news Ben

    See you on a cruiZe soon eh? :zlove::zlove::zlove:
     
  11. BlaZeit

    BlaZeit New Member

    Messages:
    939
    Likes Received:
    0
    Trophy Points:
    0
    you surely will Rob I've been a little slack lately haven't i - well we better fix that up!!
     
  12. black baz

    black baz black 'n blue Bazemy

    Messages:
    9,063
    Likes Received:
    26
    Trophy Points:
    48
    good news, ben .. could have been a bit nasty..!!!

    .. re cruising .. check out pexzed's thread in coming events for a possible cruise/lunch on 4 november .. to welcome the visiting MAFI-ZED .... ???
     

Share This Page